HP HPE7-A01 Real Exam Questions
The questions for HPE7-A01 were last updated at Dec 24,2024.
- Exam Code: HPE7-A01
- Exam Name: Aruba Certified Campus Access Professional Exam
- Certification Provider: HP
- Latest update: Dec 24,2024
What is an Aruba-recommended best practice for hardening that only applies to Aruba CX 6300 series switches with dedicated management ports?
- A . Implement a control plane ACL to limit access to approved IPs and/or subnets
- B . Manually enable Enhanced Security Mode from a console session.
- C . Disable all management services on the default VRF.
- D . Create a dedicated management VRF, and assign the management port to it.
Which feature supported by SNMPv3 provides an advantage over SNMPv2c?
- A . Transport mapping
- B . Community strings
- C . GetBulk
- D . Encryption
Your Director of Security asks you to assign AOS-CX switch management roles to new employees based on their specific job requirements After the configuration was complete, it was noted that a user assigned with the administrators role did not have the appropriate level of access on the switch.
The user was not limited to viewing nonsensitive configuration information and a level of 1 was not assigned to their role.
Which default management role should have been assigned for the user?
- A . sysadmin
- B . operators
- C . helpdesk
- D . config
You are doing tests in your lab and with the following equipment specifications
* AP1 has a radio that generates a 10 dBm signal
* AP2 has a radio that generates a 11 dBm signal
* AP1 has an antenna with a gain of 9 dBi
* AP2 has an antenna with a gain of 12 dBi.
* The antenna cable for AP1 has a 2 dB loss
* The antenna cable for AP2 has a 3 dB loss
What would be the calculated Equivalent Isotropic Radiated Power (EIRP) for APT?
- A . 26 dBm
- B . 30 dBm
- C . 17 dBm
- D . -12 dBm
A network engineer recently identified that a wired device connected to a CX Switch is misbehaving on the network To address this issue, a new ClearPass policy has been put in place to prevent this device from connecting to the network again.
Which steps need to be implemented to allow ClearPass to perform a CoA and change the access for this wired device? (Select two.)
- A . Confirm that NTP is configured on the switch and ClearPass
- B . Configure dynamic authorization on the switch.
- C . Bounce the switchport
- D . Use Dynamic Segmentation.
- E . Configure dynamic authorization on the switchport
The customer needs a network hardware refresh to replace an aging Aruba 5406R core switch pair using spanning tree configuration with Aruba CX 8360-32YC switches.
What is the benefit of VSX clustering with the new solution?
- A . stacked data-plane
- B . faster MSTP converge processing
- C . dual Aruba AP LAN port connectivity for PoE redundancy
- D . dual control plane provides better resiliency
What is a primary benefit of BSS coloring?
- A . BSS color tags improve performance by allowing clients on the same channel to share airtime.
- B . BSS color tags are applied to client devices and can reduce the threshold for interference
- C . BSS color tags are applied to Wi-Fi channels and can reduce the threshold for interference
- D . BSS color tags improve security by identifying rogue APs and removing them from the network.
Describe the difference between Class of Service (CoS) and Differentiated Services Code Point (DSCP).
- A . CoS is only used to determine CLASS of traffic DSCP is only used to differentiate between different Classes.
- B . CoS is only contained in VLAN Tag fields DSCP is in the IP Header and preserved throughout the IP packet flow
- C . They are similar and can be used interchangeably.
- D . CoS has much finer granularity than DSCP
You need lo have different routing-table requirements with Aruba CX 6300 VSF configuration Assuming the correct layer-2 VLAN already exists how would you create a new OSPF configuration for a separate routing table?
- A . Create a new OSPF area, and attach VRF name.
- B . Create a new OSPF process ID with vrf name.
- C . Attach a new OSFP process ID with a custom routing table
- D . Attach OSPF process ID in the VRF configuration.
The administrator notices that wired guest users that have exceeded their bandwidth limit are not being disconnected Access Tracker in ClearPass indicates a disconnect CoA message is being sent to the AOS-CX switch.
An administrator has performed the following configuration
What is the most likely cause of this issue?
- A . Change of Authorization has not been globally enabled on the switch
- B . The SSL certificate for CPPM has not been added as a trust point on the switch
- C . There is a mismatch between the RADIUS secret on the switch and CPPM.
- D . There is a time difference between the switch and the ClearPass Policy Manager