Check Point 156-836 Real Exam Questions
The questions for 156-836 were last updated at Nov 20,2024.
- Exam Code: 156-836
- Exam Name: Check Point Certified Maestro Expert - R81 (CCME)
- Certification Provider: Check Point
- Latest update: Nov 20,2024
Question #1
When security policy is installed
- A . All SGMs receive the security policy and one by one performs an independent policy verification.
Then, all SGMs simultaneously install the policy. - B . The SMO Master receives the policy and performs a policy verification the policy is installed on the SMO Master, the SMO Master broadcasts the available package, other members retrieve the new policy from the SMO Master, then the non-SMO Master SGMs install the policy.
- C . All SGMs receive the security policy and simultaneous policy installation occurs.
- D . The policy is installed on the SMO, the SMO Master broadcasts the available package, other members retrieve the new policy from the SMO Master and perform an independent policy verification, then the non-SMO Master SGMs install the policy.
Question #2
What is the Correction Layer?
- A . Correction Layer is a daemon which corrects errors on Backplane interfaces
- B . Correction Layer is a mechanism which handles asymmetric connections in multi-appliance
system. For example, in case of NAT - C . Correction Layer is a mechanism which activated in case of asymmetric routing
- D . Correction Layer is a Layer of GAIA OS which corrects misspelled commands and allows them to execute
Question #3
What type of cluster can a Security Group can be compared to?
- A . Load Sharing Active / Active
- B . VSLS
- C . Active / Backup
- D . Active / Standby
Question #4
What kinds of transceivers are supported on Orchestrator MHO-140?
- A . SFP, QSFP, QSFP28
- B . SFP+, SFP28, QSFP
- C . SFP, SFP+, SFP28
- D . SFP, SFP+, QSFP, QSFP28
Question #5
What happens if you apply a hotfix using gClish?
- A . If you apply a hotfix using gclish, it causes an outage for the entire SG as all members reboot at roughly the same time.
- B . If you apply a hotfix using gclish, each SG members installs the hotfix and reboots after waiting it’s turn to do so.
- C . Logical groups "A" and "B" are created. Members of group "A" install and reboot first. Then members of group "B" does the same once reboots have finished with group "A."
- D . If you apply a hotfix using gclish, the operation will fail because an outage would occur.
Question #6
What is the default Distribution mode?
- A . Auto-topology
- B . User
- C . Manual-General
- D . Network
Question #7
What will happen in case of NAT of the traffic passing through Management network?
- A . This traffic will not pass correction, since it will be dropped
- B . Orchestrator will disable NAT and traffic will pass with no issue
- C . Since Management traffic is always going to SMO, it will take a care for Correction Layer and will re-distribute traffic to other Appliances
- D . This traffic will pass with no inspection
Question #8
What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?
- A . 1Gbps connectivity for Security Groups
- B . Reserved for internal purposes. Not in use.
- C . Out-of-band interfaces for access to Orchestrator itself
- D . Additional ports used as uplinks
Question #9
The ______________ command will allow users to update the specified file on all SGMs.
- A . g_update_conf_file
- B . g_all"
- C . sed
- D . g_cat
Question #10
When working with Maestro, what is the difference between using Clish and gClish?
- A . Clish commands are for testing purposes only and cannot be saved, gClish commands apply to all SG members, by default.
- B . Clish commands apply to all UP SG members, by default. gClish commands apply to all SG members, by default.
- C . Clish commands are run on the SG members. gClish commands are run on the MHO and applied to all connected SG members in a specified group.
- D . Clish commands apply only to a specific SG member. gClish commands apply to all UP SG members, by default.